Mold Qualification and Injection Molding FAI in Mexico
AmrepMexico qualifies new and transferred injection molds at supplier facilities across Mexico, then verifies the first production parts through detailed first article inspection (FAI). Our engineers witness tool trials, review process studies, and measure every characteristic, so you approve a mold and process that can produce good parts consistently.
Mold Qualification Services in Mexico
Every qualification is scoped to your part, your mold, and your industry requirements. Most programs combine several of the services below.
Mold Design and DFM Review
Before steel is cut or a transferred tool is installed, our engineers review the part and mold design for manufacturability. We look at wall thickness, gate location, draft, venting, cooling layout, and any features likely to cause sink, warpage, or fill problems.
Tool Trial Witnessing (T0, T1, and Beyond)
We attend tool trials on site at your molding supplier. Our engineers record machine settings, observe fill and ejection behavior, collect sample parts by cavity, and document every issue found so tooling corrections are clear before the next trial.
Scientific Molding Studies
A robust process is built on data, not trial and error. We witness or review the core studies used to establish a stable molding process:
- Viscosity curve study to set injection speed
- Cavity balance study for multi-cavity molds
- Pressure drop study to confirm the machine has enough pressure
- Gate seal study to set hold time
- Cooling time study to optimize cycle without hurting quality
- Process window study to define the operating limits for key parameters
Process Capability Verification
Once the process is set, we verify it can hold critical dimensions over time. Capability studies on key characteristics, such as Cpk or Ppk, show whether the process is capable or still needs work before production approval.
Process Validation Support for Medical Devices
Medical device programs often validate molding processes through installation, operational, and performance qualification (IQ, OQ, and PQ). Our engineers support suppliers in executing these protocols and verify that the documented results match what is happening at the press.
Injection Molding First Article Inspection
First article inspection confirms that the first parts from a qualified mold and process meet every requirement on the drawing. It is the final check before production approval, and it is often a formal customer requirement.
What Our FAI Covers
- Every dimension and tolerance on the drawing, including GD&T callouts
- Cosmetic requirements against approved limit samples
- Material verification against resin certifications and lot records
- Part marking, cavity identification, and date codes
- Fit and function checks where specified
- Packaging and labeling for the first shipment
Cavity-by-Cavity Verification
In multi-cavity molds, a single bad cavity can hide inside an average. We measure parts from every cavity and report results separately, so you approve each cavity on its own data.
FAI Report Formats
FAI reports can follow the format your program requires, such as AS9102 for aerospace, PPAP dimensional results for automotive, or your own customer template. Our standard first article inspection service can also be used on its own for non-molded parts.
When Mold Qualification and FAI Are Needed
Qualification is not only for brand-new tools. Any significant change to the mold, material, machine, or location can affect part quality.
| Trigger | What should be verified |
|---|---|
| New mold | Full qualification, process studies, and complete FAI |
| Mold transfer to a new supplier or to Mexico | Tool condition, process re-establishment, and FAI against original data |
| Mold repair or modification | FAI on affected features and cavities |
| New cavity added | Cavity balance and FAI on the new cavity |
| Resin grade or resin supplier change | Material verification, process review, and FAI |
| New molding machine or press size | Process window confirmation and FAI |
| Long tooling inactivity | Tool condition check and FAI before restart |
Mold Problems We Catch Before They Reach Production
Most mold issues are cheap to fix during trials and expensive to fix after launch. Our engineers look for these problems early and work with your supplier to resolve them before you approve the tool.
Unbalanced cavities
When some cavities fill before others, parts from the same shot vary in size and weight. We run cavity balance checks and measure parts by cavity so imbalances are corrected before approval.
Insufficient cooling
Hot spots in the mold cause warpage, sink, and longer cycle times than planned. We review cooling performance during trials and flag areas that need tooling or process changes.
Steel-safe features out of tolerance
Features left intentionally oversized or undersized need final adjustment once actual shrinkage is known. We measure trial parts and give the toolmaker clear data on exactly what to correct.
Poor venting
Trapped air leads to burn marks, short shots, and weak weld lines. We identify where venting falls short so it can be fixed in steel rather than masked with process settings.
Narrow process window
A process that only works within very tight settings will drift out of specification in production. We verify the operating window is wide enough to hold quality across shifts, resin lots, and normal variation.
Gate vestige and ejection marks
Cosmetic marks at gates and ejector pins can fail appearance requirements. We check these against your approved limit samples and confirm whether tool adjustments are needed.
AmrepMexico Mold Qualification and FAI Process
Every program follows the same structured path, so you know exactly what happens at each stage and what you will receive at the end.
Step 1
Requirements review. We review your drawings, specifications, cosmetic standards, and qualification requirements.
Step 2
Qualification plan. We agree on trial stages, required studies, sample sizes, and acceptance criteria with you.
Step 3
Supplier coordination. We schedule trials with your molding supplier and confirm equipment, gauges, and materials are ready.
Step 4
Trial witnessing and studies. Our engineers attend trials, record data, and witness or review process studies.
Step 5
First article inspection. We measure and inspect parts from every cavity against all drawing requirements.
Step 6
Report and recommendation. You receive the full results with a clear recommendation to approve, conditionally approve, or reject.
Step 7
Corrective action follow-up. If issues are found, we track tooling and process corrections through the next trial.
What You Receive After Mold Qualification and FAI
Every qualification and FAI package is built so your team can make an approval decision with confidence. Deliverables typically include:
- Trial reports with machine settings, observations, and photos
- Results from scientific molding studies
- Capability study results for critical characteristics
- Ballooned drawing with measurement results by cavity
- Material certification review
- A clear approval recommendation with open issues listed
Ongoing quality after approval can continue through during-production inspection and pre-shipment inspection.
We Support High-Demand Industries Across Mexico
Our engineers support mold qualification and FAI across the industries we serve, including:
- Automotive components under IATF 16949 and PPAP requirements
- Medical device components requiring validated molding processes
- Electronics housings, connectors, and enclosures
- Home appliance parts and assemblies
- Aerospace interior components requiring AS9102 FAI
- Consumer products and packaging
Local AmrepMexico Engineers Across Mexico’s Molding Hubs
Our engineers work on site at molding suppliers across Mexico’s major manufacturing regions:
- Tijuana and North Mexico, including Mexicali, Ciudad Juárez, Chihuahua, Monterrey, and Reynosa
- Guadalajara and Central Mexico, including León, Querétaro, and San Luis Potosí
- Mexico City and South Mexico, including Puebla
Join the Global OEMs Who Trust AmrepMexico
AmrepMexico has supported manufacturers in Mexico since 1994 as part of the global AMREP supplier management group. Our team started in Tijuana and Guadalajara, helping companies such as Motorola and Texas Instruments set up supplier quality assurance programs and manage their Mexican suppliers.
What sets our molding quality control services apart:
- Engineers at the press. Our team understands molding processes, tooling, and materials, so findings come with likely causes and practical fixes.
- Independent verification. We work for you, not the supplier, so qualification results reflect real tool and process performance.
- Qualification through production. The same team can move from mold approval to ongoing inspection and supplier production management.
- Coverage across Mexico. Local engineers in the north, center, and south support suppliers wherever your molds run.
Frequently Asked Questions
What is the difference between mold qualification and first article inspection?
Mold qualification confirms the tool and process can produce good parts consistently, through trials, process studies, and capability checks. First article inspection confirms the first parts from that qualified process meet every drawing requirement. Qualification proves the process works, and FAI proves the output is correct.
Why should a mold be qualified before the part is approved?
A mold that produces a few good samples is not necessarily ready for production. Problems such as unbalanced cavities, weak cooling, or a narrow process window often stay hidden until volume runs begin, when fixing them means tooling changes, sorting, delayed shipments, and requalification. Mold qualification and FAI provide evidence before sign-off that the tool is sound, the process is stable, and every part characteristic meets the drawing.
Do molds need requalification after being moved to Mexico?
Yes. A mold that ran well at one supplier will not automatically run well at another, because presses, material handling, and operator practices differ. We collect baseline data before the tool ships, inspect it for damage on arrival, and confirm the new press matches the mold’s requirements. The mold then goes through our standard qualification and FAI process, with results compared against the original approved data.
How many parts are needed for a production approval run?
It depends on your customer requirements. For automotive PPAP, AIAG guidance traditionally calls for a significant production run, commonly cited as one to eight hours of production with at least 300 consecutive parts unless the customer specifies otherwise. Other industries set their own sample sizes in the qualification plan.
What is a steel-safe dimension?
A steel-safe dimension is a feature intentionally cut so that removing more steel brings it into tolerance. Since removing steel is much easier than adding it back, toolmakers use this approach on critical features and adjust them after trial measurements confirm actual shrinkage.
Can FAI be performed with the supplier’s measurement equipment?
Yes, as long as the equipment is calibrated and suitable for the tolerances being measured. Our engineers verify calibration status and measurement methods before relying on supplier equipment, and flag any gauges that are not capable of measuring critical features.
Can you qualify hot runners and family molds?
Yes. Hot runner molds need extra attention to manifold temperature balance and gate performance, while family molds need verification that each different part fills and packs correctly in the same shot.
How long does mold qualification take?
Timing depends on mold complexity, the number of trials needed, and how quickly tooling corrections are made. A tool that passes at T1 can be approved quickly, while molds needing several rounds of steel adjustments take longer. Your qualification plan sets expected milestones from the start.
How do I get a quote for mold qualification or FAI?
Send your part drawings, mold details, supplier location, and qualification requirements to our supplier quality team. We will recommend a scope and provide a quote based on your program.
Talk to Our Engineers Before Your Next Tool Trial
Talk to AmrepMexico about mold qualification, tool trial witnessing, or first article inspection for your molding suppliers in Mexico.
Call +1 303 952 0382 (US) or +52 33 3857 7984 (Mexico), or email [email protected].